Monday 18 June 2012

POST 32 - JUNE 2012 - Chassis Mod to accommodate T5 Box

Spigot bush 
Splitting the engine and gearbox after the trial fit, I notice that the assembly grease on the end of the gearbox main shaft is only displaced around 15mm.   This explains why they supplied a new spigot bush (yet to be fitted) with the T5 box.  Fellow XK enthusiast Tony Hamnet explains - the T5 main shaft is slightly shorter than the Moss item and is also moved back 10mm by the box to bell housing conversion plate.  The new bush effectively extends the bearing surface forward by around 15mm.
New Spigot Bush extends bearing surface forwards around 15mm.
Re. my previous post and the question - what is the purpose of the T5 box additional cables and socket.  Dan at Classic Jaguar tells me they are connected to an internal switch which is only closed in the neutral position.  If placed in series with the starter solenoid feed, it means that the car cannot be started in gear. 

Modifying the chassis to accept the T5 Gearbox
With the engine bottom half and gearbox now permanently together, I suspend them over the chassis with the front engine mounts vertically aligned in order to establish what needs to be done to accommodate the gearbox rear mounting pad. 
Hate to change the chassis cross member but will no doubt consider
it worthwhile when snicking through the T5 box next summer.
The existing mounting plate needs to be removed and the vertical support plates cut back to around 35mm.  A section 8.5" wide, 30mm in and 50mm deep at the sides is the removed from the top front edge of the cross member.  I also take out a small "V" top centre to allow for the gearbox central web.

Section cut out ready to take new metal.
I really must give those shoes a polish.
Next I make up the gearbox support plate.  This is very simply two lengths of 2mm thick angle.  The top piece to fill the hole is 50/50mm by 8.5" with the vertical section cut to match the shape of the cross member, plus the "V" for the web.  The bottom piece is 35/35mm by 8.0" and will fit between the remains of the vertical supports and provide additional strength. 

Apologies for the measurement mixture but as an imperial boy and a metric man it works for me.
Simple to make but very strong - filler and support

I can't believe this is a casting error so can someone tell me
why the mounting plate is around 10 degrees from horizontal?
Another intriguing anomaly is that the gearbox mounting is at an angle of 10 degrees from horizontal. As American muscle cars use symmetrical V8's, this seems very strange. It also means that the nearside bobbin needs to be 13mm higher than the offside. Getting this right was very time consuming.

Bobbins set to allow for angle with tapered washers.  Note essential
extra long threads on bobbins to clear 15mm thick mounting.

Neatly welded in place (not by me!) with 2mm plate filling in
the sides.  Fine texture stone-guard and two pack satin finish
all made good.

Finally in place.  Output shaft centre is 2" above top of cross
member as per original moss box .
In some ways this turned out to be more straightforward than I expected but did take some time to get exactly right.  The mounting is very strong especially with the bottom piece of angle welded to the front face of the chassis cross member.   This will hopefully be helpful for others in the future.

Classics on show Stokesley - June 16th
My home town held its first Classic Car Show on Saturday 16th June, organised by the local Rotarians.  In spite of a rather poor weather forecast, a turnout of over 100 classics enjoyed an extremely good atmosphere with many old friends meeting up and enjoying the day.

A corner of the large show ground swallows up the 100 plus
classics turning up to the very first Stokesley "Classics on Show"
England's Green and Pleasant Land at its best.
Almost all Classic shows in the UK are held in fairly isolated locations in the grounds of Castles or Country houses making the participants a somewhat captive audience.   Fine for us hardcore enthusiasts, but it does understandably discourage wives and families from joining us.  This venue is a large traditional and well established English show field within a few minutes walk of a lovely old Yorkshire market town.  Interesting shops, pubs, restaurants and the picturesque River Leven offer some respite for those less involved.
Just a matter of time I think, before the list of world class venues reads - Pebble Beach,  Carmel, Amelia Island,  Stokesley, Villa d'Este,  Salon Prive'.
Congratulations and thanks to the organisers for a very enjoyable day.

Beamish Run - June 17th
'The Beamish' as it is generally known, is a 144 mile County Durham based reliability trial for vehicles manufactured before the end of 1955 (very strict).  My 140 fixed head just qualifies and is possibly the youngest of the 160 cars participating this year.  Early car manufacturers used a number of notably difficult routes, with streams to ford, long and steep gradients to ascend / descend, often with very sharp bends.  The Beamish Connects many of these trial routes together and makes for an exhilarating full days rally.  In addition to completing the course, points are also scored by answering a series of often eclectic motor related questions at each check point.  A superb day out in some of England's most beautiful countryside and loads of fun.

End of day.  XK140 and super rare Swallow Dorreti. 
Note standard British Post War Male hands in pockets stance.
XK120 came all the way from the Isle of Man

Not always green and pleasant.  I wonder how many seconds
this particular rash of wind turbines will add to the life of the earth.
As far as I know there is not a collective noun for wind turbines so
'rash' seems appropriate, as it is commonly used for unpleasant
  things that suddenly appear.
Grandsons "Chicken Pox Charlie" (left) and "The Fredster"
help with the Monday morning clean up.

Thanks Uncle Dan
http://www.classicjaguar.com/
Next Post beginning of July